Iso 8501 3

Standard Subscriptions

Imperfections at welds, edges and other areas of steel substrates are generally starting points for corrosion. In North America, the original surface prep standard was written by an architectural group in the s for steel workers in Pittsburgh. Shot abrasives are used for thin film paint coatings such as pre-fabrication primers.

International Organization For Standardization

International Organization For Standardization

Sawn and flame-cut ends and edges need treatment to ensure that the coating adheres and is of sufficient thickness. Pits and craters shall be sufficiently open to allow penetration of paint. Commercial Blast Cleaning. The cleaned surfaces should be compared with the appropriate reference photograph in the standard according to the specification.

Consequently, they should be smoothed by grinding or filing. When viewed without magnification, the surface shall be free of all visible oil, grease, dust, dirt, mill scale, rust, coating, oxides, corrosion products and other foreign matter. It is the most recent abrasive blasting standard, and not widely specified. The width of the marginal strip should ideally be at least equal to the required cover to the reinforcement, for the same exposure condition. Visible deposits of oil, grease and dirt must be spot cleaned prior to abrasive blast cleaning.

SteelConstruction.info

Particular attention needs to be paid to the blast cleaned profile because weld metal is harder and site blast cleaning is more difficult than shop blasting. Spray Foam Roof Coating Equipment. Commercial Blast Cleaning specifies that all tightly-adhering matter must go.

Because of the contamination that occurs from the welding flux, particular attention needs to be paid to cleaning off all residues. The removal of a high proportion of soluble salts from the steel surface is seen to be the major advantage of ultra-high pressure water jetting. No shadows, pronos streaks or stains are permitted. Indentations and Surface shall be roll marks shall be free from smooth indentations and roll marks.

Navigation menu

Some wet abrasive processes use inhibitors in the water to prevent rusting of the cleaned surface. Surface shall be dressed e. Modern power tooling has been developed not only to achieve a good standard of surface cleanliness and profile but also to provide near total containment of all dust and debris generated.

Comparing Surface Prep Standards - SSPC/NACE and ISO

High build paint coatings and thermally sprayed metal coatings need a coarse angular surface profile to provide a mechanical key. Several methods have been developed to measure or assess the distance between the peaks and troughs of blast cleaned surfaces. The friction surfaces are usually either unpainted or metal sprayed without sealer. Recommendations for welding of metallic materials. The following referenced documents are indispensable for the application of this document.

Each of these International Standards is in turn divided into separate parts. When choosing a coating, the owner weighs the costs of blasting and painting against the risk of a premature coating failure. Surface Preparation Abrasive Blasting. Cementitious Fireproofing Pumps. Ultra-high pressure water jetting leaves a warm surface from which traces of residual water quickly dry, but does not generate sufficient heat to cause thermal stress in the steel surface.

Standard Subscriptions

Insulation Spray Foam Insulation. In general terms, fine grades are efficient in cleaning relatively new steelwork, whereas coarse grades may be required for heavily corroded surfaces.

Navigation menu

Re-rusting can occur very quickly in a damp environment and unless the steel is maintained in a dry condition coating of the surface should proceed as soon as possible. The marginal strip should be treated as an external surface, except that only the shop coats need be applied.

Any aluminium metal spray on surfaces in contact with concrete needs to receive at least one coat of paint to prevent the reaction that may occur between concrete and aluminium. Exterior Texture Sprayer Accessories. Contact an Expert We'll help you choose the right product for your job. Near White Blast Cleaning. For example, older air-power wrenches tend to produce a fine oily or misty exhaust which may settle on the surface.

Preparation grades of welds, edges and other areas with surface imperfections. Despite the differences, the grades of cleanliness are generally thought to be compatible. End craters shall be Surface shall be free from sharp edges free from visible end craters.

Airless Paint Sprayer Accessories. Wet abrasive blast cleaning. Surface shall be Surface shall be Surface shall be free from rolled-in free from rolled-in free from rolled-in extraneous matter extraneous matter extraneous matter. Ultra-high pressure water jetting is an extremely versatile and effective method of removing paint and metal coatings, soluble salts and other contaminants from steel surfaces.

Injecting small amounts of abrasive into the water stream can induce a rougher surface profile but can also increase operating costs. Such areas are also difficult to protect by application of paints and related products. After the preparation of the surface to an acceptable standard of cleanliness and profile, it is important that the steelwork is not allowed to deteriorate.

Interior Texture Sprayers. It is important to establish whether any remaining traces of such inhibitors will be compatible with the paint coating to be applied subsequently. Surface roughness characteristics of blast cleaned steel substrates.

This can, in particular, be the case when there are requirements for the aesthetic appearance of the finish. White Metal is the highest grade of abrasive blast cleaning. For dated references, only the edition cited applies.

Related titles

Spray Foam Insulation Equipment. Industrial is specified for conditions when the existing coating is thin, well-adherent and compatible with new coating. Spill Containment Coating Sprayers. This was straightforward enough until the industry demanded a new specification for a cleanliness grade that could cut costs by replacing White Metal in situations where near-white was good enough. For large surfaces, pressure washing with soapy water is recommended, although soap residue will inhibit coating adhesion and should be rinsed off.